Two component epoxy resin for indoor 3D floor
See more pictures
Description:

Features: high hardness, high transparency, strong adhesion, suitable for flat glue, no water lines, long yellowing resistance.

- +
0
- +
0
- +
0

Product Detail
Feedback Now

120-2AB specially designed for 3D floors, photos, photo frames, badges, stickers, panels, stickers, signs etc..M120-2AB Feature:
Epoxy resin adhesive 120-2AB is transparent type, can be cured at room temperature or warming. After curing, the surface is flat, the gloss is good, no bubbles, and there are many different specifications according to the thickness of the glue, anti-yellowing performance, curing time, ratio, etc..
Properties before Hardening ↴

Epoxy120-2A Hardener120-2B
Appearance 120-2A 120-2B
Color Transparent Transparent
Specific gravity
25℃g/cm3
1.12±0.1 0.9±0.1
Viscosity25℃ 8000±500 mpa.s 160-±30 mpa.s
Usable Method Mixing Ratio A:B=3:1(Weigh Ratio)
Usable time 25℃×30-40minutes
Hardening conditions 25℃×8-12 hours or 60℃×3hours
Production Process:
.
1. Polish the ground and remove dust (if the ground is not level, it is recommended to use cement to level it by itself)

2.Apply primer (why apply primer, because there is too much dust on the cement floor, which is not conducive to the bonding of 3D paintings, but if it is a tile floor, no primer is needed)

3. Choose your favorite 3D canvas, stick it on the ground, and push it down. Be careful not to have wrinkles. The main point of laying is that the canvas is rolled up slowly, and the adhesive paper is torn back while the picture is flattened. Compaction.

4. Clean the surface, mix the transparent art resin, apply a uniform coating on the surface, and then immediately use a defoaming roller to defoam; the thicker the 3D transparent art resin, the better the texture, but the higher the cost; normal 1 square uses 0.8KG, About 1mm thickness. The art resin is a two-component, it needs to be proportioned by an electronic scale and mixed evenly.

5. Use after at least 3 days of drying.

Use Attention Issues:
.
1. Please read the label on the package clearly before dispensing glue, and confirm the proportion of A and B agent.

2. The glue dispensing tools should be clean and dry, free of dust, water and oil.

3. Mix the A and B components according to the proportions and mix them evenly, so as to avoid unevenness leading to non-curing or insufficient hardness.

4. Since the glue starts to react and heat up after mixing, the more the amount of glue, the greater the heat. At the same time, the curing time will be shortened and the usable time will be shorter. Therefore, please make an appropriate amount of glue according to the glue filling time. So as not to cause waste.

5. After dispensing the glue, seal the AB agent package to prevent debris or moisture absorption and ensure normal use next time.

6. There are a very small number of people who have mild skin allergies when they contact the glue for a long time. It is recommended to wear protective gloves when using them. If they stick to the skin, they can be wiped off with alcohol and cleaned with detergent.

7. Before mass use, please try a small amount first to master the use skills of the product to avoid errors.

Send your message to us:
×
taiyingfuhecailiaojiaoshuitu
1-3d-epoxy-floor
3d-epoxy-floor
3d-epoxy-resin-flooring
3d-epoxy-resin
3d-floor-coating
3d-floors-created-with-epoxy
3d-resin-floors
Chat with Vincent Porter
already 1 902 messages

  • Porter 19:56.PM  Sep.19,2021
    Dear sir/madam, Welcome to our website! What should I do for you?